King Kutter Free Floating Finishing Mower Manuale Utente

FREE FLOATINGFINISHING MOWERPO Box 1200305 Commerce DriveWinfield, Alabama 35594Part No 999997 www.kingkutter.com

10BEFORE PUTTING FINISHING MOWER INTO SERVICE(IMPORTANT-INSTRUCTIONS PRIOR TO START UP)SHIPPED WITHOUT OIL IN GEAR BOX AND WITHOUT GREASE INGREASE FIT

SAFETY TRAININGz Safety is a primary concern in the design and manufacture of our product.Unfortunately, our efforts to provide safe equipment can be

PREPARTIONz Never operate the tractor and mower until you have read and completely understand thismanual, the Tractor Operator’s Manual, and each of t

13OPERATIONAL SAFETYz The use of this equipment is subject to certain hazards that cannot beprotected against by the mechanical means or product desig

14OPERATIONAL SAFETY continued...z Never allow the cutting blade to contact such items. Cut material higherat first, allowing finishing mower to cle

OPERATIONAL SAFETY continued...z Pass finishing mower diagonally through sharp dips and avoid sharp dropsto prevent “hanging up” tractor and finishing

ATTACHING TO TRACTORWARNINGNever stand betweentractor and finishing mowerwhile backing up tractorto the hitch.STEP 1 Attach to tractor's categ

ATTACHING TO TRACTOR continued...STEP 5Place and hold inner PTO shaft section next to outer section and checkif PTO shaft is too long. Each section

18STEP 1Cutting the PTO shaft to length.NOTE: Be sure to cut equallengths of each PTO shaft section.Clamp end of PTO shaft in a viceand cut off shiel

OPERATING INSTRUCTIONSThis mower was designed to CUT LAWN GRASS ONLY. Use of your finishingmower to cut any material other than lawn grass may damage

FINISHING MOWER OPERATIONSTEP 1Before each use perform the maintenance described in maintenance section(pg# 21)STEP2Read, understand, and follow the i

MAINTENANCE1). Periodically check and maintain proper gear oil level.2). Every 8 hours, grease spindles (3), roller axle (1), wheel forks (4), wheelax

TO REPLACE BELT:STEP 1 Remove top cover.STEP 2 Release adjustment spring.STEP 3 Loosen nut on adjustment pulley to allow for movement. (See Fig-ure

23Figure DFigure E

TO REPLACE BELT:STEP 1 Remove top cover.STEP 2 Loosen nut on adjustment pulley to allow for movement. (See Fig.“D”)STEP 3 Loosen nut on right side of

4 FT. FINISHING MOWER ONLY25

MAINTENANCE SAFETYz Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.z Follow good shop practices.z Keep service

27SAFETY SIGN LOCATIONSThe types of safety signs and locations on the equipment are shown in theillustration below. Good safety requires that you fam

281

2923

3TO THE PURCHASERThis manual contains valuable information about yournew King Kutter Mower. It has been carefully prepared togive you helpful suggesti

4530

67831

91032

111233MODEL NO.DESCRIPTIONSN# XXXXXXXXXX

34FINISHING MOWER

*1B-108 2B-133 3B-148 4B-16235Ref.No.Part NamePart Number4' 5' 6'7'1 Top Cover 124684 124685 124686 124687234567891010111213141

Ref.No.Part Name1470221Roll Pin Kit234Male Tube End YokeImplement End YokeFemale Tube End Yoke500131151045151040151050Tractor End YokeInner Tube 14 S

Blade Spindle UnitRef.No.Part Name5023005023011 & 2Bearing Kit-(2) Ball Bearings(6205),(2)Seals (TCM25X52X7TC), (4)Snap Rings5550093 5023114 50231

3840 HP GEARBOX

39Ref.No.Part Name Gearbox1 Snap Ring23579111213141516171910846Input Seal (NAK35X54X10)Front CapFront Cap GasketSnap RingSnap RingBearing (Hoover 208)

4It is the purchaser and/or operator’s responsibility to….zzzzz Read and understand the information contained inthis manual.zzzzz Operate, lubricate,

40BONDIOLI- (BYPY)1). There are 3 white tabs around the cover as shown in (A in FIG. 1). Take ascrewdriver and press against the tabs one at a time wi

41 BONDIOLI COVER REMOVALFIGURE- 1 FIGURE- 2 EUROCARDAN SERIES 4 COVER REMOVALFIG

EUROCARDAN SERIES 51). There are 2 black tabs around the cover as shown in (B in FIG. 1). Take aflat screwdriver and pry under the tabs one at a time

431. Limited Warranty.King Kutter, Inc. (“King Kutter”), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail purchaser(“Purchaser”

5CONTENTSITEM PAGESafety ... 6Assembly Instructions ...

6SIGNAL WORDS:The signal words DANGER, WARNING and CAUTION are used with thesafety messages in this manual and with each safety signs. They aredefine

7EQUIPMENT SAFETY GUIDELINESz Safety of the operator and by standards is one of the main concerns in designing anddeveloping a mower. However, every

8FINISHING MOWER ASSEMBLY INSTRUCTIONSSTEP 1With finishing mower still in crate, lay flat on a level surface. Remove the top& side sections of the

9 Figure A Figure B